Honda Odyssey
Vanity Mirror Light Bulb Replacement Guide
How to change a burnt out vanity mirror
light bulb in the sun visor of a 3rd generation 2005-2010 Honda Odyssey.
2008 Odyssey Sun Visor |
Flip Open Mirror Cover |
Notch Bottom Edge |
This
automotive maintenance tutorial was specifically written to assist
owners of the third generation (2005, 2006, 2007, 2008, 2009 & 2010)
Honda Odyssey minivan in changing a burnt out vanity mirror light
bulb located in the sun visor. Owners of other Honda or Acura vehicles such as the Accord, Civic, Crosstour, CR-V, CR-Z, HR-V, Fit, Element, Insight, Pilot, Ridgeline, Clarity, Crosstour, Elysion, ILX, TSX, TLX, TL, RLX, RDX, NSX and MDX may also find these DIY instructions to be helpful. A few compatible replacement miniature fuse style bulbs with their part numbers include the following: TS-14V1CP, TS-14V1.5CP, 6614F, Eiko 40842, ACDelco 13502343, Putco 230003 and the iJDMTOY 3-SMD-5050 LED. The only tool needed to access and replace the light bulbs is a small flathead screwdriver or a plastic pry bar tool. |
||
|
||
Insert Screwdriver |
Pry Out Lens Cover |
Old Light Bulb Exposed |
To prevent from
scratching the plastic surfaces, I'd recommend either covering the tip of
your screwdriver with a thin micro fiber cloth or instead use a small
plastic
pry bar tool. Insert the blade of the small flathead screwdriver into the notch at the bottom edge of the translucent plastic lens cover. Gently pry out the bottom edge of the lens cover. Then pull out the tab at the top edge of the lens cover. Set the lens cover aside in a safe place. |
||
Gently Pry Out Light Bulb |
Pull Out Old Light Bulb |
Old Light Bulb Removed |
Very gently pry out
the metal end cap at the bottom of the old light bulb. Do not apply pressure to the glass part of the light bulb to prevent from having it shatter and send shards of glass flying into your face and eyes. Remove the old light bulb from the socket. |
||
|
||
Empty Bulb Socket |
Push In New Light Bulb |
New Light Bulb Working |
Push a new
miniature fuse style light bulb such as the
TS-14V1CP
or the
6614F
straight into the socket. If you would like to have brighter vanity mirror lights, install some compatible 6614F LED bulbs. |
||
Line Up Lens Cover |
Insert Tab - Top Edge |
|
Line up the plastic
lens cover with the light housing. First, re-insert the plastic tab at the top edge back into its slot. |
||
Lens Cover Replaced |
Testing New Light Bulb |
Close Mirror Cover |
Then gently snap in
the retaining clip on the bottom edge. Make sure that the lens cover is flush with the housing at every edge. The new light bulb should have turned on immediately as soon as you pushed it into the socket. If it didn't, open and close the mirror cover or press the "Unlock" button on the key fob to re-activate the interior lights. If you installed an LED bulb and it doesn't work. Try removing it, rotating it 180 degrees and pushing it back into the socket again. It might be a "polarized" bulb. For more, check out all of my
2005-2010 Honda Odyssey DIY Repair & Maintenance Guides. |
If you found this guide to be helpful,
please consider making a small donation by clicking on the PayPal.com
"Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.) |
Copyright 2024 © PaulsTravelPictures.com
All Rights Reserved ®
Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. |
Privacy Policy About Paul & Author Contact Info