Paul's Travel Pictures

Dodge Ram 1500 Headlight Bulbs Replacement Guide
How to change a burnt out low/high beam headlight or turn signal bulb in a 4th generation 2009-2013 RAM 1500 truck.

Main Menu            Home           Digital Cameras

Misc. Pictures            Articles            My Blog

2012 Ram 1500 Headlight
Pry Up Pop Rivet Fastener
Friction Fastener Removed
This automotive "how-to" guide was specifically written to assist owners of the fourth generation (2009, 2010, 2011, 2012, and 2013) Dodge RAM 1500 truck in replacing a burnt out combination low and high beam bulb or front turn signal light bulb in the headlight assemblies.

Owners of other Dodge, Ram Trucks, or Chrysler vehicles such as the Dart, Avenger, Challenger, Charger, Durango, Journey, Grand Caravan, 2500, 3500, 4500, 5500, C/V Tradesman,  200, 300 and Town & Country may also find these DIY instructions to be helpful.

Replacement headlight bulbs with their part numbers are as follows: Combination Low & High Beam Bulb # H13 (9008) or Low Beam # H11 & High Beam # 9005 (for models with two separate bulbs), and Front Turn Signal # 3157A (Amber - 2009 to 2011 model years) or # 3157 (clear - 2011 to 2013 Model years).

The tools needed change the headlight bulbs include a flathead screwdriver, a 10mm socket and a ratcheting wrench.

Pry Out Inner Fastener
Pry Out Inner Pop Rivet
Inner Fastener Removed
To gain access to the headlight bulbs, you'll first need to remove the black plastic radiator shield and also the front grille of the vehicle.

Use the flathead screwdriver to pry out the four "pop rivet" friction fasteners that hold the black plastic radiator cover in place at the front of the engine bay.

Passenger Side Fasteners
Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-008 Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-009
Fourth Fastener Removed
There are two fasteners near the center of the vehicle and two near the outer edges.

It may be easier to just leave the fasteners in the radiator cover rather than pulling them entirely out. If the pop rivets do come out, set them aside in a safe place.

Radiator Cover Removed
Four 10mm Grille Bolts
Course Thread Outer Screw
The front grille of the truck is held in place by four 10mm screws at the top and two friction fastener clips at the bottom.

Remove the four bolts by turning them counter clockwise with the 10mm socket and ratcheting wrench.

Remove Inner 10mm Bolt
Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-014 Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-015
The two inner screws that are inserted into the metal frame are shorter and have fine threads.

The two outer screws that go in to a plastic bracket are longer and have course threads.

Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-016 Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-017
Four Grille Screws Removed
Inner Screw - Outer Screw
Set the four 10mm grille screws aside in a safe place.
Gently Pull Grill Outward
Release Clips At Bottom
Upper 10mm Headlight Bolt
Tilt the top of the grille slightly outwards and then gently pull out the two friction fasteners at the bottom.

Set the grille aside in a safe place.

Upper Screw Removed
Lower Vertical 10mm Screw
Remove Lower Bolt
The headlight assembly is held in place by two 10mm screws and a white plastic slide lock in the wheel well area.

The upper screw is horizontally mounted while the lower screw is orientated vertically.

2nd Headlight Bolt Removed
Two 10mm Headlight Bolts
Turn Wheel To Opposite Side
Remove the two screws with the 10mm socket and ratcheting wrench by turning them counter clockwise. Set them aside in a safe place.

Turn the wheels all the way to the opposite side of the burnt out headlight bulb that you are replacing.

Wheel Well Access Panel
Pry Out Inner Piece
Inner Piece Removed
Move to the wheel well liner or "splash guard" and locate the single fastener that secures the rectangular access panel.

Pry out the smaller center piece of the fastener first with the flathead screwdriver and then pry out the larger outer piece.

Pry Out Fastener
Open Splash Guard Panel
White Plastic Slide Lock
Open the wheel well access panel and wedge it on the top of the tire to hold it in place.

Use a flashlight to locate the white plastic slide lock that holds the headlight in place.


Push Up Lock To Release
Gently Pull Out Headlight
Turn Headlight Over On Bumper
Push the slide lock straight up to release it. If you have trouble releasing the slide lock up, push the headlight backwards with your other hand.

Carefully pull the headlight housing off the front of the vehicle, turn it over, and rest it on the bumper.

To help avoid scratching the painted bumper or the plastic headlight lens, place a towel in between them.

1/4 Turn Counter Clockwise
Pull Out Headlight Bulb
Red Lock Tab
Grasp the base of the headlight bulb socket and rotate it 1/4 turn counter clockwise before pulling it straight out of the housing.

Slide the red locking tab on the power connector straight back to unlock it.

Slide Red Tab Down
Press Green Release Button
Pull Off Power Plug
Press the green release button on the power connector and separate it from the old headlight bulb.
Philips H13 12V 60/55W
Headlight Bulb Socket
Insert New H13 Bulb
Insert a new # H13 combination low and high beam headlight bulb in to the housing and rotate it 1/4 turn clockwise to secure it in place.

Try to avoid touching the glass part of the new halogen bulb with your fingers or anything dirty in the engine bay.

If you do get the bulb dirty, wipe it clean with an alcohol moistened paper towel.

Push On Power Connector
Turn Signal Bulb Socket
1/4 Turn Counter Clockwise
Push the green plastic power connector straight on to the base of the new bulb until it clicks in to place.
Pull Out Socket
Pull Bulb Straight Out
1/4 Turn Clockwise
Rotate the smaller black plastic turn signal light bulb socket 1/4 turn counter clockwise and pull it straight out of the housing.

Pull the old turn signal bulb straight out of the socket and push in a new clear # 3157 / 3157K bulb or an amber colored 3157A bulb depending on your model year.

Insert the socket back in to the housing and rotate it 1/4 turn clockwise to lock it in place.

Testing New Headlight Bulbs
Insert Upper 10mm Screw
Insert Lower Vertical Screw
Test the new bulbs by turning on the headlights and activating the hazard signals.

Push the headlight assembly back in to place and insert the two 10mm screws.

Tighten Lower 10mm Bolt
Lower Screw Replaced
Tighten Upper 10mm Bolt
Tighten the two headlight screws with the 10mm socket and ratcheting wrench.
White Plastic Slide Lock
Push On Headlight Housing
Pull Slide Lock Down
Move to the wheel well access panel and pull the white plastic slide lock in to the down position.

If you have trouble moving the slide lock, push on the headlight with your other hand while sliding the lock down.

Headlight Slide Lock Engaged
Close Access Door
Insert Larger Outer Piece
Close the wheel well liner access panel and insert the larger outer piece of the fastener at the bottom.

Pop in the smaller inner piece of the wheel well liner fastener.

Push In Smaller Inner Piece
Grille Fastener & Slot
Grille Friction Fastener
Line up the friction fasteners at the bottom of the grille with the slots on the front of the vehicle.
Slot On Front of Truck
Push On Bottom of Grille
Insert Outer 10mm Screw
Push the bottom of the grille in place until you hear the two friction fasteners click.

Replace the four grill screws and tighten them with the 10mm socket and ratcheting wrench.

Inner 10mm Grille Screw
Tighten With 10mm Socket
Be sure to install the shorter screws with fine threads in to the inner holes and the longer course threads screws in to the outer holes.
Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-073 Dodge-Ram-1500-Headlight-Bulbs-Replacement-Guide-074
4 Grille Screws Replaced
Plastic Radiator Cover
Line up the black plastic radiator cover on the front of the engine bay.

Push the four pop rivet fasteners in place.

Push In 4 Pop Rivets
Friction Fasteners Secured
Test New Low/High & Signal
Test the new bulbs by turning on the headlights, flashing the high beams and activating the hazard signals.

For more, check out my other Dodge RAM 1500 Repair & Maintenance Guides.

If you found this guide to be helpful, please consider making a small donation by clicking on the "Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.)

Main Menu       Home       Digital Cameras

Misc. Pictures       Articles       My Blog


Copyright 2021
 All Rights Reserved

Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to

Privacy Policy     About Paul & Author Contact Info