Paul's Travel Pictures

Mitsubishi Outlander Sport Windshield Wiper Blades Replacement Guide
How to change the windshield window wiper blades on a 3rd generation 2011-2017 Mitsubishi Outlander Sport SUV.

Main Menu            Home           Digital Cameras

Misc. Pictures            Articles            My Blog

2015 Outlander Sport Wipers
Lift Wiper Arm Off Window
This automotive maintenance tutorial was specifically written to assist owners of the third generation (2011, 2012, 2013, 2014, 2015, 2016 and 2017) Mitsubishi Outlander Sport in changing the windshield window wiper blades.

Owners of other Mitsubishi vehicles such as the Lancer, Outlander, Mirage, ASX, RVR, Galant, I-MIEV, Montero, Eclipse, 3000GT, Endeavor, Raider, Diamante, Attrage, Carisma, Colt, Grandis, Magna, Pajero and the Space Star may also find these DIY instructions to be helpful.

The OEM wiper blade sizes in inches are as follows: Driver Side 24" and Passenger Side 21".

A few compatible replacement wiper blades with their part numbers are as follows: Bosch 24A & Bosch 21A, Rain-X RX30224 & Rain-X RX30221, Anco 31-24 & Anco 31-21, Michelin 8024 & Michelin 8021, Valeo 900241B & Valeo 900211B, Trico 25-240 & Trico 25-210, PIAA 95060 & PIAA 95053 and ACDelco 8-4424 & ACDelco 8-4421.

The only tool needed to remove and replace the wiper blades is a small flathead screwdriver or a plastic pry bar tool.

Plastic Lock Tab
Gently Pry Open Lock Tab
The first step is to lift the wiper arm off the windshield until it remains in the raised position by itself.

Use a small flathead screwdriver or a plastic pry bar tool to gently lift open the bottom edge of the rectangular shaped lock tab near the center of the wiper blade.

Pull Wiper Blade Down
Remove Metal Hook
Swing the lock tab up to release the old wiper blade.

Gently pull the old wiper blade down to remove it from the metal hook at the end of the wiper arm.

Rotate the old wiper blade until it is almost parallel to the wiper arm.

Pass the metal hook at the end of the wiper arm through the hole in the center of the old wiper blade.

Towel - Protect Glass
Line Up New Blade & Hook
Place a towel on the windshield to protect the glass from being scratched, chipped, cracked or shattered just in case the metal wiper arm smacks down on to the window while you are changing the wiper blade.

Line up the new wiper blade with the wiper arm. The rubber blade should be facing up and away from the windshield.


Pass Hook Through Opening
Rotate Blade Parallel
Pass the hook at the end of the wiper arm through the opening in the center of the new wiper blade.

Rotate the wiper blade until it is just about parallel with the wiper arm.

Pull Blade Up In To Hook
Snap In Locking Tab
Firmly pull the new wiper blade up until it clicks securely in to the hook at the end of the wiper arm.

Swing the locking tab down and gently snap it back in to place.

Double check that the new wiper blade is securely attached to the wiper arm.

Lower Wiper To Window
Wiper Blades Replaced
Gently lower the wiper blade and arm down on to the windshield.

For the best wiper performance, thoroughly clean off the windshield and apply a window treatment product that will repel water such as Rain-X.

For more, check out all of my 2011-2017 Mitsubishi Outlander DIY Repair & Maintenance Guides.

If you found this guide to be helpful, please consider making a small donation by clicking on the "Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.)

Main Menu       Home       Digital Cameras

Misc. Pictures       Articles       My Blog


Copyright 2021
 All Rights Reserved

Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to

Privacy Policy     About Paul & Author Contact Info