Paul's Travel Pictures

Nissan Juke Headlight Bulbs Replacement Guide
How to change a burnt out low/high beam headlight, front turn signal or side marker bulb in a 2010-2016 Nissan Juke.

Main Menu            Home           Digital Cameras

Misc. Pictures            Articles            My Blog

2014 Nissan Juke Headlight
Low & High Beam Headlight
Headlight Power Plug
This automotive maintenance tutorial was specifically written to assist owners of the first generation (2010, 2011, 2012, 2013, 2014, 2015 & 2016) Nissan Juke in changing a burnt out dual low & high beam headlight bulb, front turn signal or side marker (parking) light bulb.

Owners of other Nissan vehicles such as the Versa, Sentra, Altima, Maxima, Cube, Leaf, Pathfinder, 370Z, Rogue, Xterra, Murano, Armada, Quest, Frontier and Titan may also find these DIY instructions to be helpful.

Replacement bulbs with their part numbers are as follows: Low/High Beam # 9007, Turn Signal # 7507 (or PY21W) and Front Side Marker LIght # 194NA (or 194A).

No tools are needed to change any of the headlight bulbs in either the driver or passenger side housings.

Electrical Connector
Press Tab - Release Plug
Twist Off Plastic Ring
The combination Low & High beam headlight bulb is located in a separate housing below the other lights.

If necessary, you may choose to remove the windshield washer fill tube to gain better access to the headlight bulb on the passenger side of the vehicle.

Reach in behind the headlight housing and pull the power connector straight off the base of the old bulb.

Then twist off the black plastic locking ring 1/4 turn in the counterclockwise direction.

If you have trouble removing the plastic ring, try pushing in while turning it counterclockwise.

Locking Ring Removed
Remove Old Bulb
Sylvania 9007 Low/High
Once the plastic locking ring has been removed, you can pull the old bulb straight out of the housing.

The owner's manual states that you should first pull out the rubber dust cover. I didn't find that to be necessary.

On previous model years or international versions of the Nissan Juke, the headlight bulb may be held in place by a metal arm or "clip". To release the arm, press in and move the end of the arm out of the metal hook. For an example of this metal retaining arm, check out my Nissan Cube Headlight Bulbs Replacement Guide.

How To Release Power Plug
Plug Clip Released
Empty Bulb Socket
The two pictures in the row above show you how to release the plastic retaining clip on the electrical connector.

If you have trouble releasing the clip by pushing down on the tab, you may need to carefully use a small flathead screwdriver to pry it up.

Insert New # 9007 Bulb
Line Up New Bulb
New 9007 Bulb In Place
Try to avoid touching the glass part of the new halogen headlight bulb with your fingers or anything greasy in the engine bay.

If you do get the new bulb dirty, wipe it clean with an alcohol moistened paper towel.

Insert the new # 9007 low/high beam bulb in to the headlight housing.

You may need to rotate it back and forth until you get the tabs properly lined up inside the socket.


Plastic Locking Ring
1/4 Turn Clockwise - Lock
Push On Power Plug
Spin on the black plastic locking ring 1/4 turn in the clockwise direction to secure the new bulb in place.

Push the power plug straight on to the base of the new headlight bulb.

(If your Juke has a metal retaining arm to secure the headlight bulb, swing it closed over the new bulb and insert the end of the arm in to the metal hook.)

Test New Headlight Bulb
Turn Signal & Parking Light
Front Turn Signal Socket
The Front Turn Signal and Front Side Marker (Parking) light bulbs are located in the upper housing.

Rotate the white plastic turn signal bulb socket 1/4 turn counterclockwise and pull it straight out of the housing.

1/4 Turn Counterclockwise
Push Down & 1/4 Turn CC
Turn Signal Bulb Housing
Push the old bulb down in to the socket and rotate it 1/4 turn counterclockwise before pulling it straight out.

Push a new amber colored # 7507 or PY21W bulb down in to the socket and rotate it 1/4 turn clockwise to secure it in place.

1/4 Turn Clockwise - Lock
Parking & Side Marker Light
Side Marker Bulb Socket
Re-insert the turn signal light bulb socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.

The Side Marker / Parking light bulb is located near the top of the upper housing.

Rotate the small grey side marker bulb socket 1/4 turn counterclockwise before pulling it straight out of the housing.

1/4 Turn Counterclockwise
Pull Out Old # 194NA Bulb
Side Marker Bulb Housing
Pull the old side marker bulb straight out of the socket and push in a new amber colored # 194NA or 194A bulb.

If you want brighter side marker lights, there are 194NA LED options available.

1/4 Turn Clockwise
Test New Headlight Bulbs
Testing High Beam Filament
Re-insert the side marker bulb socket in to the housing and rotate it 1/4 turn clockwise to secure it in place.

Test the new bulbs by turning on the headlights, activating the hazard signals and flashing the high beams.

For more, check out my other Nissan Juke DIY Repair Guides.

If you found this guide to be helpful, please consider making a small donation by clicking on the "Donate" button located to the right of this paragraph. Thank you!
(Note: I am not a registered charity. Donations are not tax deductible.)

Main Menu       Home       Digital Cameras

Misc. Pictures       Articles       My Blog


Copyright 2021
 All Rights Reserved

Paul's Travel Pictures is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to

Privacy Policy     About Paul & Author Contact Info